JD80-02 Details & Specifications :

General Overview 

• Model: JD80-02 — Emergency Stationary Standby 

• Power Rating: 80 kWe Standby 

• Fuel: Diesel 

• Frequency: 60 Hz at 1800 RPM 

• UL 2200 & cUL Listed; CSA Certified 

• EPA Tier 3 Certified 

• Voltage Options: 120/240V Single Phase (1.0 PF) or 277/480V Three Phase (0.8 PF) 

• Paint Color: White (Standard) / Gray (Optional) 

• Warranty: 2 Year / 2000 Hour Standby Limited 

• Single Source Supplier — factory load tested 

Engine 

• Manufacturer: John Deere 

• Model: 4045HF285 — PowerTech E 4.5L 

• Type: 4-Cycle, In-line 4 Cylinder 

• Aspiration: Turbocharged with Charge Air Cooling (CAC) 

• Displacement: 275 cu. in. (4.50 L) 

• Bore x Stroke: 4.19 in. x 5.00 in. (10.6 cm x 12.7 cm) 

• Compression Ratio: 19.0:1 

• Rated RPM: 1800 

• Max HP Standby: 126 HP (94.0 kWm) 

• Governor: Electronic Isochronous 

• Fuel Injection: Denso HP3 / L16 ECU Controller 

• EPA Certification: Tier 3 (CARB & EPA certified) 

• Cooling: Radiator Cooled, Unit Mounted, 50°C Ambient 

• Oil Drain Extension: Plumbed to Bulkhead Fitting in Base 

Engine Performance Data 

• Exhaust Gas Temp (Stack): 1,069°F (576°C) 

• Exhaust Gas Volume at Stack Temp: 651 CFM (18.4 m³/min) 

• Max Allowable Exhaust Restriction: 30.0 in. H₂O (7.50 kPa) 

• Fuel Consumption at 100% Load: 6.34 gal/hr (24.0 lit/hr) 

• Fuel Consumption at 75% Load: 5.21 gal/hr (19.7 lit/hr) 

• Fuel Consumption at 50% Load: 3.92 gal/hr (14.8 lit/hr) 

• Aspirating Air Flow: 234 CFM (6.62 m³/min) 

• Air Flow Required (Radiator Cooled): 6,541 CFM (185 m³/min) 

• Total Oil System Capacity: 3.43 gal (13.0 lit) 

• Engine Jacket Water Capacity: 2.24 gal (8.50 lit) 

• System Coolant Capacity: 5.40 gal (20.4 lit) 

• Water Pump Flow Rate: 48.0 GPM (182 lit/min) 

• Heat Rejection to Coolant: 2,990 BTUM (52.3 kW) 

• Heat Radiated to Ambient: 1,632 BTUM (28.6 kW) 

• Deration: Rated power available to 10,000 ft (3,048 m) at ambient up to 122°F (50°C) 

Alternator / Generator 

• Alternator Model (480V): Stamford UCI224G 

• Type: Brushless, Single Bearing 

• Connection (480V): 12 Lead Wye, High Wye 

• Voltage Regulation: ±1% 

• Poles: 4 Pole, Rotating Field 

• Insulation Class: Class H (125°C rise over 40°C ambient — standby) 

• Winding: Double Layer Concentric, 2/3 Pitch, 12 Leads 

• Stator Resistance: 0.055 Ohms per phase at 22°C (series star) 

• Rotor Resistance: 0.94 Ohms at 22°C 

• Protection Rating: IP23 

• Standards: NEMA MG1-32, BS5000, IEC34, CSA C22.2, BS EN 60034 

• 100% of Rated Load — One Step Block Loading 

• Maximum Harmonic Content: 5% 

• Maximum Overspeed: 2250 RPM 

• Rated Power Factor: 0.8 

• Bearing (Drive End): Ball 6312-2RS (ISO) 

• Bearing (Non-Drive End): Ball 6309-2RS (ISO) 

Voltage Regulator 

• Model: Stamford AS440 Automatic Voltage Regulator (AVR) 

• Type: Half-wave phase controlled thyristor, Surface Mount Technology (SMT) 

• Sensing Input Voltage: 190 to 264VAC (1 phase) 

• Power Output: 82VDC at 200VAC input 

• Continuous Current: 4A; Transient: 7.5A for 10 seconds 

• Voltage Regulation: ±1% 

• Thermal Drift: 0.03% per 1°C change in AVR ambient 

• Soft Start Ramp Time: 3 seconds 

• AVR Response: 20 ms 

• External Voltage Adjustment: ±10% with 1k ohm, 1 watt trimmer 

• Under Frequency Protection Set Point: 94 to 98% Hz 

• Over Excitation Protection Set Point: 65VDC (10–15 sec fixed delay) 

• Unit Power Dissipation: 12 watts maximum 

Control Panel — Blue Star DCP7310 

• Type: Microprocessor Based Digital Gen-Set Controller (Auto Start) 

• Mounted facing left from generator end (unless specified otherwise) 

• Display: 4-Line Back-lit LCD with menu navigation 

• Inputs: 8 programmable/configurable contact inputs 

• Outputs: 10 contact outputs (6 DC configurable + 2 volt-free relay) 

• Communications: CAN Bus (J1939), RS485, USB, MODBUS RTU & TCP 

• PC Software: Licence-free DSE Configuration Suite 

• Remote SCADA monitoring via DSE Configuration Suite 

• Event Recording: Configurable log (250 events) 

• IP65 Rating (with supplied gasket) — water ingress resistance 

• NFPA 110 Level 1 Compatible 

• cULus Listed, CE Approved 

• Standard Shutdowns: Low Oil Pressure, High Coolant Temp, Overspeed, Overcrank 

• Emergency Stop Pushbutton with Audible Alarm Buzzer and Silencing Switch 

• DSENet® expansion compatible 

Enclosure 

• Level: Level 2 — Weatherproof Enclosure with Sound Attenuation Foam 

• Material: Powder Coated 14 Gauge Steel 

• Wind Rating: 200 MPH certified per IBC2021 and ASCE/SEI 7-16 

• Sound Attenuation: 1.5" Thick Polydamp Type D Acoustical Foam (PAF) installed in enclosure 

• Roof: Pitched for increased structural integrity and improved watershed 

• Intake: Punched intake with baffle; punched exhaust openings 

• Doors: Keyed alike lockable with draw down latches and stainless steel component hinges 

• Fasteners: All stainless steel 

• Base: Formed steel with mounting and lifting holes 

• Vibration Isolation: Mounts to isolate unit from base rail 

• Finish: Cardinal Industrial Hammer Textured Semi-Gloss Polyester Powder Coat 

• Seismic Certified: IBC 2021 

• Standard Colors: White / Gray (Custom colors available) 

Sound Data 

• Measured at 23 feet (7 meters) per ISO 8528-10 

• OPU: No Load 77 dBA / Full Load 81 dBA 

• Level 1 Enclosure: No Load 74 dBA / Full Load 77 dBA 

• Level 2 Enclosure: No Load 71 dBA / Full Load 73 dBA 

• Level 3 Enclosure: No Load 65 dBA / Full Load 67 dBA 

Cooling System 

• Cooling: Unit Mounted Radiator — 50°C (122°F) Ambient Rating 

• Coolant Capacity (System): 5.40 gal (20.4 lit) 

• Water Pump Flow Rate: 48.0 GPM (182 lit/min) 

• Heat Rejection to Coolant: 2,990 BTUM (52.3 kW) 

• Thermostat Opens at: 180°F (82°C); Fully Open at 203°F (95°C) 

• Radiator Duct Flange available (OPU only) 

Electrical Accessories 

• Mainline Breaker: 125 Amp, 3 Pole, 480V — Mounted & Wired in NEMA 1 Enclosure 

• Battery System: 12 Volt with Rack and Cables 

• Battery Charger: BC1206A Series — 12V, 6 Amp, 2-Stage, UL 1236 Listed 

• Jacket Water Heater: TPS Series — 1500W, 120VAC, Rated -20°F — with Isolation Valves and Wired to Terminal 

• Air Cleaner: Dry Single Stage 

• Silencer: Critical Grade Compact CPJ Series — Mounted to Engine 

• Flexible Fuel Connector included 

Fuel Tank Options 

• Standard: 24-Hour / 250-Gallon Sub-Base Tank with Stub-Up Area 

• Option: 48-Hour / 500-Gallon Sub-Base Tank 

• Option: 72-Hour / 750-Gallon Sub-Base Tank 

• All tanks: UL 142 Listed, Double Wall construction with Secondary Containment 

• Includes: Supply & Return Connections, Fuel Level Gauge, Fuel Leak Switch, Fill & Vent Plumbing 

• Tank construction: Heavy gauge steel with Diamond Vogel Nexgen or Cardinal Industrial powder coat 

• Electrical stub-up area standard to provide wiring provisions through the base 

• Interior tank baffle separates cold supply fuel from hot returning fuel 

• Direct reading fuel level gauge and low fuel level / fuel leak alarms standard 

Certifications & Compliance 

• UL 2200 & cUL Listed 

• CSA Certified 

• EPA Tier 3 Certified (CARB & EPA) 

• Seismic Certified to IBC 2021 

• NFPA 110 / CSA C282 Compliant 

• 200 MPH Wind Rated — IBC2021 & ASCE/SEI 7-16 

• ISO 8528-10 Sound Measurement Standard 

• Factory Load Tested per MIL-STD-705C 

• NEMA MG 1, IEEE and ANSI Standards Compliance 

Voltage Ratings Summary 

• 240V / 1 Phase / 1.0 PF — Generator: UCI274E, 12 Lead DD, 80 kWe, 333 Amps 

• 208V / 3 Phase / 0.8 PF — Generator: UCI274C, 12 Lead Wye, 80 kWe, 278 Amps 

• 240V / 3 Phase / 0.8 PF — Generator: UCI274C, 12 Lead Delta, 80 kWe, 241 Amps 

• 480V / 3 Phase / 0.8 PF — Generator: UCI224G, 12 Lead Wye, 80 kWe, 120 Amps 

• 600V / 3 Phase / 0.8 PF — Generator: UCI224G, 4 Lead Wye, 80 kWe, 96 Amps 

• All ratings: 125°C Temperature Rise over 40°C Ambient 

• Standard configuration as quoted: 480V / 277V Three Phase 

product specifications:

product related documents:

JD80-02 Engine Data Sheet 12-5-23.pdf

2026 EPA Cert 350haj-tjdxl04-5119-005 JD80-02, JD100-01.pdf

JD80-02_SpecSheet.pdf

JD80-02_Drawings.pdf

JD80-02.pdf